Anti-slip Safety-Grip – Red / White

The Heskins Safety-Grip™ non-slip strips were originally designed for use in various industries, but are of course suitable for a wide range of applications. The anti-slip mats come in a variety of forms, from single- or double-component materials, as well as glued tapes with and without anti-slip materials. Anti-skid is essential safety equipment in many workplaces for safety and health reasons. Slippery and slippery slush can form on almost all floor surfaces under various conditions such as wetness, soap, frost, dust and gross dirt and many other things that are in our environment. Heskins manufactures many types of safety and non-slip boards in different roughness and designs, also various markings (colors and signs) for floors and corridors in warehouses and warehouses. All Heskins products meet the highest standards and are suitable for all situations, whether in business or at home.

General information about sizes and colors of Safety-Grip™

Heskins Safety-Grip™ anti-slip strips are available in various widths from 19mm to 1168mm. Widths from 10mm up to 18mm can be special ordered, but those sizes must always be ordered in minimum quantities. The sizes that are in stock at the supplier are the following: 25mm, 50mm, 75mm, 100mm and 150mm. All widths come on rolls with a total length of 18.3 meters.

• Lengths: There are 18.3 meters of anti-skid tape per roll
• Width (standard widths in stock): 25 mm, 50 mm, 75 mm, 100 mm and 150 mm (it is possible to get the non-slip strips wider by special order)
• Roughness: You can get the non-slip strips in "Standard" which is the lowest roughness, "Coarse" and "Extra rough" which is the highest roughness.
• Color options: Black, Red, Yellow, Blue, Green, Grey, Brown, White, Clear, Fluorescent Yellow, Black/Yellow (Hazard), Red/White (Caution), Orange.

Attention! not all types of roughness can be obtained in colors.

• Standard – Least Coarseness: All available colors listed above.
• Coarse – Medium coarseness: Black, Yellow, Green, Black/Yellow (Hazard).
• Extra Coarse: Black, Green.

Roughness of skid plates (with abrasives)?

Standard – Lowest roughness

Coarse – Medium coarseness

Extra Coarse – Highest coarseness

Are the roughs available in all colors?

The short answer is no! All colors are available in Standard skid plates: All colors and all Note, not all colors or sizes are in stock, the sizes of the Safety-Grip skid plates range from 19mm up to 1168mm. Some colors and sizes are only accepted by special order, the rolls can be cut to suit from 19mm up to 1168mm, contact us for information on prices and delivery times.

How long does a special order take?

• Standard shipping usually takes 10-15 business days.
• Express shipping with TNT and DHL takes 2-6 business days.

ATTENTION! there will be an additional cost for express delivery.

Standard roughness is usually sufficient indoors, be it stairs or floor surfaces. Coarse and Xtra-coarse are very suitable as a lot of dirt (sand, gravel, mud, snow, water) can accumulate in the tape, these conditions are created in work areas, step boards on work machines and equipment, steel ladders and steps, floor surfaces to name a few . But even if something accumulates in the rough slippery surfaces, it is usually rough and porous enough that it provides good grip in these conditions. Note that it can fill up well, and then you have to clean the non-slip surface.

What is the best way to put down a skid plate?

• You have to make sure that the surface is clean and completely free of grease, you can get various materials for cleaning under gluing that do not leave any film (chemical residue) on the surface after cleaning.
• If non-slip boards are laid on rough and porous floor surfaces such as wood, concrete and the like, it is good to prime them with a special primer to achieve the best adhesion to the surface.
• The Safety-Grip™ non-slip mats come with an adhesive on the back, which is a film that is removed from them, similar to adhesive mats in general.
• The non-slip board is pressed down with a hand roller, rolled firmly over it to press it down as best as possible.
• If the ice board is in a high traffic area and under a lot of stress, "Edge Sealer" is used, but it is a sticky substance that is applied to the edge of the board so that it does not peel up.
• There is a very powerful and strong adhesive on the Heskins Safety-Grip™ non-slip boards and is sufficient in most cases if the surface is very good.

The video below shows how this is done.